Flowserve Machinery Components Manual do Utilizador descarregar pdf

1. Drawing, Brief Description, Explosion Protection, Function of a Mechanical Seal ......2

2. Safety ...............................................................3

3. General ..............................................................4

4. Transport, Storage ......................................................5

5. Equipment Check .......................................................5

6. Mechanical Seal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

6.1 Installation of Cartridge Type Seal with Setting Plates........................8

6.2 Installation of a Cartridge Type Seal with Centring Tabs ......................9

6.3 Installation of a Component Type Seal...................................10

6.4 Installation of Seals with Hooked Type Sleeves ............................11

7. Piping Instructions .....................................................12

8. Performance Testing of Pumps ...........................................12

9. Functional Recommendations.............................................13

10. Shut Down, Disassembly ................................................14

11. System Check ........................................................15

12. Spare Parts, Repair.....................................................15

These installation instructions can be used for the following seal types:

Pusher seals: Allpac 4 series, Allpac N series, Centipac 1 series, CRO, D series, DHT

series, Europac 306, Europac 6 series, FRO, GSD, GSL, HD series, HSC,

HSH, LD, P series, Q series, RO, Simpac 3 series, SRO, U series, UHT

series.

Bellows seals: BRC series, BX series, BXH series, BXLS series, BXRH, CBR series, CBS,

GSDH, PBR, PBS, X series.

General Installation and Maintenance Instructions

for Machinery Components

USER INSTRUCTIONS

-Original Instruction-

Table of Contents page no.

Experience In Motion

1 2 3 4 5 6 ... 15 16

Resumo do Conteúdo

Página 1 - -Original Instruction

1. Drawing, Brief Description, Explosion Protection, Function of a Mechanical Seal ...2 2. Safety ...

Página 2

106.3 Installation of a Component Type Seal See figure 8. 6.3.1 Check assembly drawing, bill of material and seal components prior to installatio

Página 3

General Installation and Maintenance Instructions for Machinery Components116.4 Installation of Seals with Hooked Sleeves (overhung pumps) See fig

Página 4

126.4.11 After bringing the unit up to operating conditions (pressure and temperature), recheck pump to driver alignment. Make adjustments as necessa

Página 5 - 5. Equipment Check

General Installation and Maintenance Instructions for Machinery Components13and face materials require special precautions to prevent damage to the se

Página 6

149.8 Liquid seal requirements: Do not start the equipment dry. Open valves to flood equipment with product. Vent all air and/or product vapor from

Página 7

General Installation and Maintenance Instructions for Machinery Components15Product may be released during removal of the mechanical seal. Safety meas

Página 8

To ﬁnd your local Flowserve representative and ﬁnd more about Flowserve Corporation, visit www.ﬂowserve.comFIS144eng REV 12/2009 Printed in USAF

Página 9

21. Drawing, Brief Description, Explosion Protection, Functional Requirements This mechanical seal is designed to provide reliable performance u

Página 10

General Installation and Maintenance Instructions for Machinery Components3 ESA position statement: http://www.europeansealing.com/statements.html

Página 11

4The ultimate user must ensure that personnel assigned to handle, install and run the mechanical seal and related equipment is well acquainted with th

Página 12

General Installation and Maintenance Instructions for Machinery Components54. Transport, Storage

Página 13

65.7 The equipment must be earthed to prevent sparks due to static electricity discharge.Shaft runout should not exceed 0,05 mm (.002”) TIR (Total In

Página 14

General Installation and Maintenance Instructions for Machinery Components7Concentricity of the shaft to the seal chamber bore should be within 0,025

Página 15

86.1 Installation of Cartridge Type Seal with Setting Plates See figure 6.6.1.1 Check assembly drawing, bill of material and seal assembly

Página 16 - Order #___________________

General Installation and Maintenance Instructions for Machinery Components96.2 Installation of a Cartridge Type Seal with Centring Tabs See figure

Modelos relacionados Mechanical Seal General

Comentários a estes Manuais

Sem comentários

Flowserve Machinery Components Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Flowserve Machinery Components. Flowserve Machinery Components User Manual Manual do Utilizador

Resumo do Conteúdo

Modelos relacionados Mechanical Seal General

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Flowserve Machinery Components